KCB1600齒輪泵流量96m3/h,壓力0.6Mpa,吸入真空高度2米,效率42%,口徑150,配用電機為Y45KW-4

KCB1600性能曲線圖:

  KCB齒輪油泵在輸油系統中可用作傳輸、增壓泵；KCB gear oil pump in the oil system can be used as a transport, booster pump;

   在燃油系統中可用作輸送、加壓、噴射的燃油泵；In the fuel system can be used as a transport, pressure, jet fuel pump;

   在一切工業領域中，均可作潤滑油泵用。In all industrial areas, can be used as lubricating oil pump.

   KCB齒輪泵主要有齒輪、軸、泵體、安全閥、軸端密封所組成。齒輪經熱處理有較高的硬度和強度，與軸一同安裝在可更換的軸套内運轉。泵内全部零件的潤滑均在泵工作時利用♌輸出介質而自動達到。KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal. Gear after heat treatment with high hardness and strength, and shaft installed in the replaceable shaft sleeve. In all parts of the lubrication pump are pump work automatically to achieve using the output media.

   泵内有設計合理的洩油和回油槽，是齒輪在工作中承受的扭矩力最小，因此軸承負荷小，磨損小，泵效率高。Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.

   泵設有安全閥作為超載保護，安全閥的全回流壓力👉為泵額定排除壓力的1.5倍，也可在允許排出壓力範圍内根據實際需要另外♊調整。但注意本安全閥不能作減壓閥的長期工作，需💋要時可在管路✏️上另🏃‍♂️行安裝。從主軸外伸端向🐕泵看，為順時針旋轉。Pump is equipped with safety valve as overload protection, the total reflux pressure relief valve is rated pump out pressure of 1.5 times, also can allow discharge pressure range according to actual needs and adjust. But note that this cannot be a long-term work pressure reducing valve, relief valve can be installed in the piping shall be separately when necessary. To pump from the main shaft overhang end to see, for clockwise.